800-364-0287
Pli-dek

Get Your Plywood Ready For Waterproofing

 

murrieta-job_procoat_f-system-123

Get Your Plywood Ready For Waterproofing

 

Not all decks are constructed of pressure treated timbers. Many are surfaced with plywood. This material is created by layering thin wooden boards that are compressed and glued together with the wood grains opposing one another. Preparing a plywood deck for waterproofing installation is the first step in preserving a plywood decking project. Waterproofing is essential whether the plywood has been installed for indoor flooring or outside decking. Sealing the substrate prevents moisture damage that can lead to:

  • Rot
  • Mold
  • Warping
  • Mildew
  • Curling or peeling away of adhered surface materials such as linoleum or paint.

Plywood is a common choice of materials for substrate. As a flooring or decking surface material, plywood is versatile, economical and easy to work with. Using the right construction and finishing methods, plywood substrates become durable and long-lasting. For the best results in waterproofing a plywood deck, start with the right preparation techniques.

#1. Inspect It

  • Thoroughly inspect every inch of the substrate for soundness and quality.
  • Repair or replace as necessary.
  • Confirm that substrate is securely fastened to supports.
  • Inspect cracks of seams carefully. Use a putty knife to pry out any debris.
  • Cover seams with flashing paper then caulk edges and seams.

#2. Drains & Openings

If a plywood deck has a drain it should be constructed of galvanized or stainless steel and be properly flanged. Cast iron or plastic are unsuitable drain materials. Shower drains are not designed for use in a decking system. If a copper drain is installed special care must be taken to avoid contact between dissimilar metals that can cause rust and corrosion.

#3. Prepare The Surface

  • Remove contaminants that might interfere with the adhesion of the sealant such as paint or oil.
  • Use a broom and give the surface a thorough sweeping to remove debris and dirt.
  • With a stiff bristled push-broom scrub the substrate vigorously to remove any debris that may be stuck to the surface.
  • Sweep again and make certain that the plywood is completely dry.

#4. Apply Primer

Apply a single layer of base coat. The first coat will penetrate into the substrate. When it cures it will strengthen the plywood from the inside out. It creates the conditions for the sealant to adhere permanently to the surface of the plywood.

#5. Patch & Prepare

After the base coat has completely dried, inspect the substrate once again. Patch any cracks, holes, joints or seams with a rubberized base mixture. It’s consistency should be similar to that of caulk. If any rough areas are present, smooth them out with a coating of the same mixture. Caulk all junctions where the substrate meets a wall.

#6. Apply The Membrane

Once caulking and patches are dry, it is time to apply the rubberized membrane that will completely waterproof the plywood surface.

#7. Finishing Touches

After the sealant has cured, final finishing can then be performed. The plywood surface can be painted or texturized according to personal preference.

#8. The Top Coat

When the final finish has cured, one last top coat seals the entire project to add a final layer of protection to a plywood deck that is easy to clean, seamless, slip resistant and, best of all, waterproof.

How To Get Yours

With plywood substrate popular with DIY enthusiasts, as well as designers on a budget, this material is commonly found throughout homes and commercial structures. The most important thing to do in order to get the most out of this building material is to use professional products and apply them with the methods professionals advise. The temptation to take a shortcut may arise. Don’t do it.

The best products on the market, such as the PLI-DEK waterproofing deck system, have been developed over years of professional laboratory testing and research. To achieve the results the product promises, as well as retain the benefit of a manufacturer warranty, it is important to follow manufacturer application instructions. For more information on sealant products and the best techniques of application, please contact us.

 

Leave a Reply

Your email address will not be published. Required fields are marked *

 

Contact Pli-Dek Systems, Inc.

41610 Date St #104
Murrieta, CA 92562
Toll Free: 800-364-0287
Fax: (951) 834-9551

Connect with Pli-Dek

We can do Web Design and Web Maintenance by AJH Creative & Design